Leave Your Message

UF Membrane Module PVC Ultrafiltration Membrane Module UFc50C Stainless Steel Housing Household Water Purification

● Membrane module housing and other components are 304 stainless steel material;

● Sealing resin and membrane material reach food grade standards;

● PAN material can be used for liquid filtration with alcohol concentration <60%;

    Product Overview

    UFc50C  is  capillary  hollow  fiber  membrane  made  of  high  polymer  material, which is a separating product that will not have any phase change. The modified PVC material adopted to this product has good permeable rate, good mechanical strength, good  chemical  resistance  anti-pollution  ability,  MWCO  is  100k  Dalton.  Membrane ID/OD  is  1.0mm/1.8mm,  filtering  direction  is  inside-out,  that  is  raw  water  flows inside the hollow fibers and, driven by differential pressure, permeates outwards so as to filter  bacteria, colloids, suspended substances,  microbes, and other  harmful substances.

    Applications

    Production of mineral water, mountain spring water and other germ-free liquid;

    Drinking treatment of tap water, surface water, well water and river water;

    Pre-treatment of RO device;

    Treatment, recycle and reuse of industrial wastewater

    Filtration Performance

    According to the service conditions of modified PVC hollow fiber ultrafiltration membrane which  are  applied to various water  sources, the  product  is  proved to reach below filtration effects:

    Water Composition Filtering Effect
    Suspended Substances, Particles >1um Removal Rate ≥99%
    SDI ≤ 3
    Virus, Bacteria >4 log
    Turbidity <0.1NTU
    TOC Removal Rate 0-25%

    Above data is obtained when turbidity of feed water is less than 15NTU. The product  is  proved  to  reach  the  sanitary  standards  of  drinking  water  by  Health Department  of  Guangdong  Province.  Approval  number  is  YUE  WEI  SHUI  ZI  2014S1671.

    Product Parameters

    Product Appearance

    1
    Figure 1 Product Dimensions

    Inner Filter

    2

    Figure 2 Inner Filter Dimensions

    Technical Parameters:

    Structure inside-out
    Membrane Material Modified PVC
    MWCO 100K Dalton
    Nominal Membrane Area 5.4m2
    Membrane ID/OD 1.0mm/1.8mm
    Module Dimensions Φ105mm×1110mm
    Connector Dimensions 3/4 "  Female Thread

    Application Data:

    Pure Water Flux 1,700L/H (0.15MPa, 25ºC)
    Designed Flux 35-100L/H (0.15MPa, 25ºC)
    Operating Pressure ≤0.2MPa
    Maximum Trans Membrane Pressure 0.2MPa
    Maximum Operating Temperature 45ºC
    Operating PH Range 4-10
    Washing PH Range 2-12
    Operating Mode Cross-flow/Dead-end Filtration

    Feed Water Requirements:

    A security filter, precision <50 micron, should be set as pretreatment of UF, in case of  blockage caused  by  large  particles  in  raw water. Attention:  UF  membrane material is macromolecular organic plastics, raw water must not contain any organic solvents.

    Feed Water Turbidity ≤15NTU
    Oil & Grease ≤2mg/L
    Feed Water SS ≤20mg/L
    Total Iron ≤1mg/L
    Continuous Feeding Residual Chlorine ≤5ppm
    COD Suggested ≤500mg/L

    Component Material:

    Component Material
    Membrane Modified PVC
    Sealing Epoxy Resins
    Housing SUS304

    Typical Operating Parameters:

    Maximum Backwashing Pressure 0.2MPa
    Backwashing Flow Rate 100-150L/m2 .hr
    Backwashing Frequency Every 30-60 minutes
    Backwashing Duration 30-60 seconds
    CEB Frequency 0-4 times/day
    CEB Duration 5-10 minutes
    CIP Frequency 1-3 months
    General Washing Chemicals :
    Disinfection 15ppm NaClO
    Organic Contamination Washing 0.2% NaClo+0.1% NaOH
    Inorganic Contamination Washing 1-2% Citric Acid /0.2% HCl

  • Previous:
  • Next:

  • Baidu
    sogou